收藏本站
AT45DB081B
should take place in a maximum of time t EP . During this time, the status register will indi-
cate that the part is busy.
Additional Commands
MAIN MEMORY PAGE TO BUFFER TRANSFER: A page of data can be transferred
from the main memory to either buffer 1 or buffer 2. To start the operation, an 8-bit
opcode, 53H for buffer 1 and 55H for buffer 2, must be followed by the three reserved
bits, 12 address bits (PA11 - PA0) which specify the page in main memory that is to be
transferred, and nine don’t care bits. The CS pin must be low while toggling the SCK pin
to load the opcode, the address bits, and the don’t care bits from the SI pin. The transfer
of the page of data from the main memory to the buffer will begin when the CS pin tran-
sitions from a low to a high state. During the transfer of a page of data (t XFR ), the status
register can be read to determine whether the transfer has been completed or not.
MAIN MEMORY PAGE TO BUFFER COMPARE: A page of data in main memory can
be compared to the data in buffer 1 or buffer 2. To initiate the operation, an 8-bit opcode,
60H for buffer 1 and 61H for buffer 2, must be followed by 24 address bits consisting of
the three reserved bits, 12 address bits (PA11 - PA0) which specify the page in the main
memory that is to be compared to the buffer, and nine don’t care bits. The CS pin must
be low while toggling the SCK pin to load the opcode, the address bits, and the don’t
care bits from the SI pin. On the low-to-high transition of the CS pin, the 264 bytes in the
selected main memory page will be compared with the 264 bytes in buffer 1 or buffer 2.
During this time (t XFR ), the status register will indicate that the part is busy. On comple-
tion of the compare operation, bit 6 of the status register is updated with the result of the
compare.
AUTO PAGE REWRITE: This mode is only needed if multiple bytes within a page or
multiple pages of data are modified in a random fashion. This mode is a combination of
two operations: Main Memory Page to Buffer Transfer and Buffer to Main Memory Page
Program with Built-in Erase. A page of data is first transferred from the main memory to
buffer 1 or buffer 2, and then the same data (from buffer 1 or buffer 2) is programmed
back into its original page of main memory. To start the rewrite operation, an 8-bit
opcode, 58H for buffer 1 or 59H for buffer 2, must be followed by the three reserved bits,
12 address bits (PA11 - PA0) that specify the page in main memory to be rewritten, and
nine additional don’t care bits. When a low-to-high transition occurs on the CS pin, the
part will first transfer data from the page in main memory to a buffer and then program
the data from the buffer back into same page of main memory. The operation is inter-
nally self-timed and should take place in a maximum time of t EP . During this time, the
status register will indicate that the part is busy.
7
2225J–DFLSH–2/08
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
AT45DB161B-TI IC FLASH 16MBIT 20MHZ 28TSOP
AT45DB321-TC IC FLASH 32MBIT 13MHZ 32TSOP
AT45DB321B-TI IC FLASH 32MBIT 20MHZ 32TSOP
AT45DB321C-TC IC FLASH 32MBIT 40MHZ 28TSOP
AT45DB642-TC IC FLASH 64MBIT 20MHZ 40TSOP
AT88CK9000-8TH CRYPTO PROGRAMMER BOARD 8-TSSOP
AT88SC12816C-MJ IC EEPROM 128KBIT 1.5MHZ M2J
AT88SC25616C-MJ IC EEPROM 256BIT 1.5MHZ M2J
相关代理商/技术参数
AT45DB081B-TI-2.5 功能描述:闪存 8M SERIAL 2.7V - 2.5V IND TEMP RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
AT45DB081B-TU 功能描述:闪存 8M 28 I/O Pins SPI 264B 2.7V RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
AT45DB081D 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-megabit 2.5-volt or 2.7-volt DataFlash
AT45DB081D_07 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-megabit 2.5-volt or 2.7-volt DataFlash
AT45DB081D_08 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-megabit 2.5-volt or 2.7-volt DataFlash
AT45DB081D_09 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-megabit 2.5-volt or 2.7-volt DataFlash
AT45DB081D_13 制造商:AD 制造商全称:Analog Devices 功能描述:8-megabit 2.5V or 2.7V DataFlash
AT45DB081D-DWF 制造商:Adesto Technologies Corporation 功能描述:WHOLE WAFER, NO BACKGRIND - Gel-pak, waffle pack, wafer, diced wafer on film